Shop
ADHESIVE REMOVING PLIERS
The Adhesive Removing Plier is used for remove composite material after debonding of orthodontic brackets and attachments from the teeth. The one side of plier comes with ¼” pad one the working ends the other side has a scraper replaceable blade with hex key allowing to remove extra composite material without damaging the tooth.
BIRD BEAK PLIER WITH CUTTER
The Bird Beak Plier with cutter is designed for versatile and precision. The cone and the flat pyramid beaks are for creating multi sizes loops. The cutter added at the end of the beaks with tungsten carbide sharp cutting blades can easily cut stainless steel wires.
| WIRE TYPE | MINIMUM | MAXIMUM |
|---|---|---|
| ROUND | .012” (.30mm) | .025” (.64mm) |
| RECTANGULAR | .016” × .016” (.41mm × .41mm) |
.025” × .025” (.56mm × .64mm) |
TORQUING PLIER FEMALE
The female torquing plier is use to offering precise control over torque application to the adjustment of archwires. This plier ensures that each tooth align into the correct position. The plier allows for accurate torque at the exact points on the archwire, providing high level of control to make minor but important adjustments. These adjustments help to guide the teeth into the desired position and improve the overall alignment.
| WIRE TYPE | MINIMUM | MAXIMUM |
|---|---|---|
| ROUND | .016” (.41mm) | .020” (.51mm) |
| RECTANGULAR | .016” × .016” (.41mm × .41mm) |
.022” × .028” (.55mm × .71mm) |
HAMMERHEAD CINCH BACK PLIER
The Hammerhead Cinch Back Plier is specially designed for Niti wires for making a bend on distal end. The serrated tip makes a firm grip and makes the wire study while bending the distal end of Niti archwires .The ergonomic design is for providing precise control and smooth working.
| WIRE TYPE | MINIMUM | MAXIMUM |
|---|---|---|
| ROUND | .016” (.41mm) | .020” (.51mm) |
| RECTANGULAR | .016” × .016” (.41mm × .41mm) |
.025” × .025” (.64mm × .64mm) |
JARABAK PLIER
The Jarabak Plier is designed for bending light wires. The construction with small and very fine cone for making loops and springs. The micro serrated tip provides excellent control and grip. The grooves ensures uniformity in wire bending and closing loops.
| WIRE TYPES | MINIMUM | MAXIMUM |
|---|---|---|
| ROUND | .012” (.30mm) | .022” (.56mm) |
JARABAK PLIER WITH CUTTER
The Jarabak Plier with cutter is designed for bending light wires. The construction with small and very fine cone for making loops and springs. The micro serrated tip provides excellent control and grip. The grooves ensure uniformity in wire bending and closing loops. The feature added cutter at the end of the beaks with tungsten carbide sharp cutting blades can easily cuts stainless steel wires.
| WIRE TYPES | MINIMUM | MAXIMUM |
|---|---|---|
| ROUND | .012” (.30mm) | .022” (.56mm) |
KIM PLIER
Kim Plier With Cutter is designed for making multiple edgewise loops on archwires. The three steps loop forming tip have diameter 1.8mm, 2.8mm and 3.8mm. The tungsten carbide wire cutter at the end of the tip can easily cuts orthodontic wires.
| WIRE TYPE | MINIMUM | MAXIMUM |
|---|---|---|
| ROUND | .014” (.36mm) | .020” (.51mm) |
| RECTANGULAR | .016” × .016” (.41mm × .41mm) |
.025” × .025” (.64mm × .64mm) |
LIGHT PLIER WITH 2-GROOVE
The light wire with groove is designed with long cone and pyramid flat beaks used to give very fine and precise loops on light wires up to 0.20” (0.51 mm). The two parallel groove at the tips allowing to make duplicate and triplicate loops and the grooves also ensure the firm grip on wires for helping out banding, holding and placing.
| WIRE TYPES | MINIMUM | MAXIMUM |
|---|---|---|
| ROUND | .012” (.30mm) | .020” (.51mm) |